←  Skilifts.org Technical Discussions

Skilifts.org / SORT Forum

»

Reverse Operation

Cameron's Photo Cameron 15 Mar 2005

I'm just telling you what I saw and heard. While I can't be sure that the reason is correct, the lift definitely was running backwards (I saw that with my own eyes!). The lift does start at the bottom of the resort, so maybe it's backwards to stop people from hopping on (you can walk right up to it at night).

Cameron.
Reply

highspeedquad's Photo highspeedquad 15 Mar 2005

What reason would there be to load the lift?
Reply

Allan's Photo Allan 15 Mar 2005

My guess would be to go skiing at night for free.
Reply

highspeedquad's Photo highspeedquad 15 Mar 2005

Ah, unless a hotel is up there (in which I guess they would provide acess) night skiing seems like the most likely possibility. Might be a little dark though, better bring a flashlight.
Reply

floridaskier's Photo floridaskier 15 Mar 2005

If they could, you know some drunk or stoned high schoolers would try to catch a free ride up at night wearing miner's lamps (or not). Then one of them would get hurt, and it would be the resort's fault, they would get sued, etc.
Reply

Bill's Photo Bill 15 Mar 2005

Plus its running really slow, so it would be tough on the body if its below freezing.
Reply

pete643's Photo pete643 18 Mar 2005

Remembering my days as a early 20 something, we would think that it would be cool to ride it up backwards after we got drunk. Wouldn't matter if it was running slow, it would just make it easier to hop on backwards!
Reply

lift_electrical's Photo lift_electrical 30 Mar 2005

All the Doppelmayr detachs I have worked on run in reverse. The speed is limited to 1 meter. There are ways to make the lift run 5 meters in reverse.........There are several reasons for reverse run. One is to have a grip that has failed a grip force check run in reverse back into the station and unload the carrier. Another would be loading chairs back on the line when using a dead end park rail as mentioned several times earlier. Last it is an easy way when doing your preseason testing to check the limit switch that is in the enclosure where the bullwheel tach is mounted. Run the lift in reverse, switch to forward and try and start the lift. You should not be able to restart because the limit switch is tripped. Hold your blue over ride button while starting the lift for about an 1/8 of a bullwheel revolution and the limit switch will reset. I am not 100% sure but I think in reverse operation, if the lift should run away, the brakes will be applied by a Reference-Actual or an Actual-Actual fault depending what is going on to cause the runaway. So not all the rollback safeties are bypassed.
Reply

yardsale's Photo yardsale 01 Apr 2005

coskibum, on Feb 6 2004, 08:04 PM, said:

Ok i had a question today while skiing...why would a lift need to operate in reverse.  there was a trivia question by one of the lifties that said "what is the only lift that can go in reverse at copper?"  well the obvious answer was timberline and it was indeed correct according to him.  does anyone know why one would need this feature and why don't lifts made by Poma go backwards too?

thanks!
<{POST_SNAPBACK}>



For maintenace being able to run in reverse is a key time saver,Poma`s dont run in reverse cause they dont need mayntnunce!
Reply

liftmech's Photo liftmech 01 Apr 2005

Really! Then I should quit right now!
Reply

Skiing#1's Photo Skiing#1 06 Mar 2012

View Postlift_electrical, on 30 March 2005 - 12:18 PM, said:

All the Doppelmayr detachs I have worked on run in reverse. The speed is limited to 1 meter. There are ways to make the lift run 5 meters in reverse.........There are several reasons for reverse run. One is to have a grip that has failed a grip force check run in reverse back into the station and unload the carrier. Another would be loading chairs back on the line when using a dead end park rail as mentioned several times earlier. Last it is an easy way when doing your preseason testing to check the limit switch that is in the enclosure where the bullwheel tach is mounted. Run the lift in reverse, switch to forward and try and start the lift. You should not be able to restart because the limit switch is tripped. Hold your blue over ride button while starting the lift for about an 1/8 of a bullwheel revolution and the limit switch will reset. I am not 100% sure but I think in reverse operation, if the lift should run away, the brakes will be applied by a Reference-Actual or an Actual-Actual fault depending what is going on to cause the runaway. So not all the rollback safeties are bypassed.


Other reason: any skiers hang on the chair...they have to have reverse and bring them down to safe.

http://www.youtube.c...feature=related
Reply

SkiLiftsRock's Photo SkiLiftsRock 06 Mar 2012

Here is another good reason as to why the lift might have to go in reverse:

http://www.youtube.c...h?v=XH-tLteRVJ4

5 people loaded a quad. How can you do that?? Tight squeeze in the carrier!
Reply

Peter's Photo Peter 07 Mar 2012

View PostSkiLiftsRock, on 06 March 2012 - 09:30 PM, said:

Here is another good reason as to why the lift might have to go in reverse:

http://www.youtube.c...h?v=XH-tLteRVJ4

5 people loaded a quad. How can you do that?? Tight squeeze in the carrier!


This happened right in front of me at Crystal a few years ago. Although the lift operator didn't notice. When I told him the last chair had 5 people on it he just looked up and laughed. Wasn't a Doppelmayr so there wasn't much he could have done I guess.

Attached File(s)

Reply

liftmech's Photo liftmech 07 Mar 2012

Not the first time I've seen that on that particular lift....
Reply

LiftTech's Photo LiftTech 09 Mar 2012

Our new Poma 6 pack detach (LPOA terminal) runs in reverse, only 500 fpm, even has a backup alarm, to not run in reverse is now an option.
Reply

cjb's Photo cjb 12 Mar 2012

Running in reverse is also handy to correct spacing issues. We had our high clutch misbehaving the other day so we run the lift in reverse, stalled the chair that had previolusly stalled in forward operation and avoided laps of long over-rides.
Reply

chairliftsrcool's Photo chairliftsrcool 12 Mar 2012

Speaking of reverse, saw the UC Quad at Copper go in reverse about ten minutes before openening yesterday.
Reply

liftmech's Photo liftmech 12 Mar 2012

Standard weekly test there on UC/H-lift.
Reply

2milehi's Photo 2milehi 14 Mar 2012

Any reason for that weekly test? When I was at Keystone there was no weekly test for Reverse. Summer maintenance was the only "test".
Reply

liftmech's Photo liftmech 16 Mar 2012

I'm guessing because it's new? I should clarify it's not a true weekly in that it's not on the required form. I'd bet we don't do it after this first 'break-in' season. We don't on Timberline.
Reply